電話相談窓口 (平日10:00-18:00):03-6803-0563 各種お問い合わせに関して 会社概要（アクセス）
MENU
カート
03-6803-0563
検索
詳細検索
MENU
検索
ダイレクト•デジタル•マニュファクチャリング 迅速でプロフェッショナルなオンデマンド3Dプリンティング 詳しくはこちら
Categories
3Dプリント

【技術サポート U007】エラーコードと解決方法_UltiMaker_全機種


お使いのUltiMaker 3Dプリンターには、正しく安全に動作するための複数のセンサーや安全機能が組み込まれています。本ページでは、一般的なエラーコードと、その状況を解決するためのガイドへのリンクを掲載しています。

クイックリンク

UltiMaker Sシリーズエラーコード

Difference between detected height of both PrintCores exceeds realistic values
ER27 – Unspecified error
ER28 – Print core max temp
ER29 – Print core min temp
ER30 – Build plate max temp
ER31 – Print core heater error
ER32 – Z axis stuck or limit switch broken
ER33 – X or Y axis stuck or limit switch broken
ER34 – Print head communication error
ER35 – I2C communication error
ER36 – Safety circuit error
ER37 – Print head sensor error
ER38 – Active leveling correction failed
ER39 – Incorrect print temperature specified
ER40 – Incorrect build plate temperature specified
ER41 – Motion controller failed to update
ER42 – Print job not suitable for printer
ER43 – Flow sensor error
ER44 – Unable to download firmware due to lack of space on printer
ER45 – Capacitive sensor low performance or interference detected
ER50 – Unexpected filament position in Material Station
ER51 – Filament too short for use with Material Station
ER52 – Decoupler obstructed
ER53 – Filament too short for use with Material Station
ER54 – Filament loading unsuccessful
ER55 – Filament too short for use with Material Station
ER56 – Printer feeder filament pickup unsuccessful
ER57 – Material Station filament loading error
ER58 – Material Station could not react to Ultimaker S5 Printing
ER59 – Material Station could not react to the Ultimaker S5 during unloading
ER60 – Prefeeder unable to move filament during startup
ER61 – Material Station failed to unload material
ER62 – Filament sensor error
ER63 – Unknown error
ER64 – Cannot select / grayed out material on Material Station
ER65 – Flow sensor error
ER66 – Decouplers not calibrated
ER67 – Dehumidifier is not working correctly
ER68 – The humidity in the Material Station is high
ER70 – An expected error occurred during unloading material from bay X from extruder X
ER71 – Printcore EEPROM read zero
ER80 – Expected Air Manager is missing
ER86 – Air Manager fan is unable to rotate at the desired speed
ER998 – An unspecified error has occurred
ER999 – An unspecified error has occurred
The material failed to load wizard

UltiMaker 2+ Connect エラーコード

ER201 – Detected nozzle temperature is invalid
ER202 – The print head is not heating up steadily
ER203 – The detected build plate temperature is invalid
ER204 – Z axis stuck or limit switch broken
ER205 – X or Y axis is stuck or limit switch is broken
ER206 – Detected move outside normal volume. Please reslice your print.
ER207 – There was a serial communication within the electronics
ER208 – There was a communication error
ER209 – Detected error within the electronics
ER210 – Detected error with the power supply
ER211 – There was a communication error in the printer
ER212 – Your file could not be processed. Please provide a valid print file and do not remove the USB drive before the print is started
ER213 – An error occured while reading the print file. Please reslice your print
ER214 – Missing SD card